EnduRaMem Design Software — UF

Welcome to EnduRaMem Design Software (EMDS) — UF Configurator

Fill in your project, water, design, process and CEB-CIP parameters and get a fully calculated ultrafiltration skid projection — hydraulics, membrane count, dosing pumps, chemical consumption and power draw — updated live as you type.

Fill Project Data, then Water Parameters.

Set Design Parameters — water type, flux, train configuration.

Set Process timing and Standby pump requirements.

Set CEB–CIP chemical cleaning parameters.

Open the Report — it recalculates live as you adjust any field.

Print or save the final projection as a PDF.

Step 1 of 5

Project Data

Project identification shown on the cover of the projection report.

Project

Date

Prepared By

Company Name

Project Name

Project No auto-assigned

Revision

Customer — Additional Information

Customer Name

Customer Contact

Description

Step 2 of 5

Water Parameter

Feed water quality used to size dosing and CEB/CIP chemical demand.

Feed Water Quality

pH2–11

Temperature °C1–40

TSS ppm0–100

Turbidity NTU0–200

COD ppm0–200

Alkalinity ppm as CaCO₃0–5000

TDS ppm0–100000

Additional Parameter, if any

Step 3 of 5

Design Parameters

Defines hydraulic basis, water type, flux strategy, train configuration and membrane selection.

Design Basis

Flow Rate M3/Hr

Water Type

Train Configuration

Nos of Train (W)

Nos of Train Standby (X)

Configuration

Operation

Flux Strategy

Design Flux Aggression

Suggest Flux? No → uses the water type/aggression table. Yes → uses your value at right.

Filtration Flux LMH

Backwash Flux LMH

CEB Flux LMH

CIP Flux LMH25–50

Membrane & Air Scour

Select UF Membrane

Active Area m²

Air Scour Flow NM3/Hr/module10–20

Step 4 of 5

Process Parameters

Cycle timing for filtration, backwash and chemically-enhanced backwash (CEB), plus standby pump requirements.

Cycle Timing

Filtration Time min30–60

Backwash Time sec40–60

Forward Flush Time sec10–30

Chem Injection Time sec120–150

Chem Rinse Time sec120–180

Chem Soak Time min10–20

Aeration Time sec10–30

Valve Pause Time sec1–15

Pump Rampup Time sec1–15

Standby Requirement

Filtration Pump

Backwash Pump

Dosing Pump

B/W pump (2W) to adj. CEB

Step 5 of 5

CEB – CIP Parameters

Chemically-enhanced backwash frequency, CIP frequency, and the chemical reference data used in dosing calculations.

CEB Frequency

Acid CEB per Day1–4

Select Acid

NaOH+NaOCl CEB per Day1–4

NaOH CEB per Day1–4

NaOCl (Hypo) CEB per Day1–12

CIP

CIP Frequency / Year1–12

CIP Tank Vol, % of Internal Hold-up

CEB-CIP Chemical Data

Chemical	Concentration (%)	Price (₹)	CEB Target	CIP Target
HCl	%	₹/Lit	pH	pH
H2SO4	%	₹/Lit	Shares the acid target pH above
NaOCl (Hypo)	%	₹/Lit	ppm	ppm
NaOH (Caustic)	%	₹/Kg	pH	pH

NaOH price is per Kg. CEB/CIP targets are pH for acids and caustic, ppm for NaOCl. The H2SO4 dosing calculation in the source workbook draws its working concentration from the NaOH(Caustic) row rather than this H2SO4 concentration field — reproduced here for an exact match.